How to Install and Upgrade a 2010 2011 2012 2013-2015 KIA Sportage GPS Navigation Bluetooth CD DVD Radio Head Unit

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

If your factory radio cannot satisfy you in car since it cannot be compatible with some upgraded features, you can think about replacing your factory radio with a new aftermarket car radio. This article aims to introduce how to remove the factory radio and install the new car radio in 2010 2011 2012 2013-2015 KIA Sportage, if you own the same or similar dashboard, you can carefully refer to the following installation steps, which may help with the installation.

2010 2011 2012 2013-2015 KIA Sportage car radio after installation
2010 2011 2012 2013-2015 KIA Sportage car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2010 2011 2012 2013-2015 KIA Sportage car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Uncover the screw covers on each corner and then remove the two screws with a screwdriver.

Uncover the screw covers on each corner and then remove the two screws with a screwdriver
Uncover the screw covers on each corner and then remove the two screws with a screwdriver
2-1
2-1

3. Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back.

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don't forget to disconnect the connectors at the back
Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back
3-1
3-1
3-2
3-2

4. Remove the panel on the right side of the radio with a plastic removal tool.

Remove the panel on the right side of the radio with a plastic removal tool
Remove the panel on the right side of the radio with a plastic removal tool

5. Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back.

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back
Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back
5-1
5-1

6. Remove four screws that are holding the radio on the dashboard.

Remove four screws that are holding the radio on the dashboard
Remove four screws that are holding the radio on the dashboard

7. Take out the original radio and unplug the connectors at the back of it.

Take out the original radio and unplug the connectors at the back of it
Take out the original radio and unplug the connectors at the back of it
7-1
7-1

8. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

9. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo
Connect the harnesses to the back of the new Seicane car stereo

10. Connect the Seicane car stereo to your original stereo’s plugs.

11. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car stereo into the dash.

13. Put everything into their original place. All the installation is done.

 

Wish you can learn some skills from the above installation instruction. If you meet any difficulties and don’t know how to overcome them, please feel free to contact your dealer, communicate with someone experienced or turn to a professional technician for help. If you still think it hard to install the new car radio, you can directly go to a car radio upgrade center to have the car radio installed by a professional technician.

Anyway, before installation, please carefully pick an ideal car radio for your beloved car. Here I’d like to share a remarkable 2010 2011 2012 2013-2015 KIA Sportage car radio from Seicane with you. Fore more details, please click:

https://www.seicane.com/hd-touchscreen-radio-for-2010-2015-kia-spotage-android-with-gps-navigation-audio-system-bluetooth-music-usb-aux-wifi-1080p-tv-mirror-link-dvr-s0495

This car radio is loaded with the stable Android 6.0 operation system and a powerful quad-core CPU processor, therefore, with this car radio installed in your car, you will embrace a much smoother, faster and easier operation experience.

There are a wide range of practical and entertainment features being offered by this all-in-one car radio, mainly including 3D GPS navigation system, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc.

Under the wireless Bluetooth technology, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, without taking your hands off the steering wheel, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone.

What are you waiting for? This unit is at a competitive price now. If you like it, just add it to your shopping cart.

The Professional Tips on a 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex Car Radio Sat Nav Audio Speaker Removal and Upgrade

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

If you would like to remove your factory radio and install a new car radio, what you need to do is to find out what features you need. And if your factory radio cannot be compatible with these features you are eager to, you can think about replacing your factory radio with a new aftermarket car radio. The following is a detailed 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio installation instruction from Seicane. If you also own the same or similar dashboard, you can refer to this instruction.

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation
2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

Here are four tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio installation instruction

1. Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery.

Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery
Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery

2. Remove trim pieces to access original car radio as follows.

Remove trim pieces to access original car radio as follows
Remove trim pieces to access original car radio as follows
2-1
2-1
2-2
2-2
2-3
2-3

3. Remove hazard warning accessory.

Remove hazard warning accessory
Remove hazard warning accessory

4. Disconnect Ribbon Harness and wiring loom.

5. Remove car radio fascia, please gently and carefully pull upwards from left hand corner.

Remove car radio fascia, please gently and carefully pull upwards from left hand corner
Remove car radio fascia, please gently and carefully pull upwards from left hand corner
5-1
5-1

6. Remove the four screws that are holding the originalcar radio in place.

Remove the four screws that are holding the originalcar radio in place
Remove the four screws that are holding the originalcar radio in place

7. Gently take out the original car radio.

Gently take out the original car radio
Gently take out the original car radio

8. Remove the original car radio’s wiring harness and antenna from the back of the car radio.

9. Remove the factory mounting brackets and install them on the new car radio.

10. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

11. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

12. Connect the Seicane car radio to your original radio’s plugs.

13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane car radio into the dash.

15. Put everything into their original place. All the installation is done.

 

Wish you can learn something useful from the above installation instruction. If you encounter any difficulties and don’t know how to overcome them, you can seek for advice from your dealer or a professional. Or during the installation, you can contact your dealer, communicate with someone experienced or turn to a professional technician. Anyway, before installation, it is essential for you to select an ideal car radio for your beloved car radio. If you have no ideas, you can refer to the following link which is a remarkable 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio from Seicane.

https://www.seicane.com/android-2008-2015-mitsubishi-lancer-ex-hd-touchscreen-gps-navigation-radio-with-fm-bluetooth-wifi-usb-1080p-video-mirror-link-obd2-rearview-camera-s04117

With this car radio installed in your car, you will freely get access to a wide range of practical and entertainment features, such as GPS navigation function, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc. Thus, this all-in-one car radio from Seicane can be taken as one of the most suitable replacements for your factory radio.

Under the guidance of turn-by-turn directions and voice prompts provided by the high-accuracy 3D GPS navigation system, you can easily know your current locations and find the right way to reach your desired destinations even you are driving around an unfamiliar place. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Through Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, Bluetooth hands-free phone calls and Bluetooth streaming music are both available for you, which can give you great convenience and enjoyment.

Wish you like this unit and good luck!

The Useful Installation Instruction on a 2014 2015 2016 Subaru Forester Car Radio with DVD Player Bluetooth GPS Navigation System

2014 2015 2016 Subaru Forester car radio after installation

It goes without saying that you may feel very tired or get bored if you have been in your car for a long time. Under this circumstance, you must want to refresh yourself, so you can listen to your favorite music, watch TV programs or play videos in your car. However, your factory radio may not support these entertainment features, so you can consider replacing your factory radio with a new aftermarket car radio. The following is a 2014 2015 2016 Subaru Forester car radio installation instruction from Seicane, which can be regarded as your reference if you own the same or similar dashboard.

2014 2015 2016 Subaru Forester car radio after installation
2014 2015 2016 Subaru Forester car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2014 2015 2016 Subaru Forester car radio installation instruction

1. Use a plastic removal tool to pry the trim panel of the original car radio.

Use a plastic removal tool to pry the trim panel of the original car radio
Use a plastic removal tool to pry the trim panel of the original car radio

2. Disconnect the connectors at the back of the trim panel.

Disconnect the connectors at the back of the trim panel
Disconnect the connectors at the back of the trim panel

3. Use a screwdriver to unscrew all the screws that are holding the original car radio in the dashboard.

Use a screwdriver to unscrew all the screws that are holding the original car radio in the dashboard
Use a screwdriver to unscrew all the screws that are holding the original car radio in the dashboard
3-1
3-1

4. Gently take the original car radio out from the dashboard.

Gently take the original car radio out from the dashboard
Gently take the original car radio out from the dashboard

5. Disconnect the connectors and cables at the back of the original car radio.

Disconnect the connectors and cables at the back of the original car radio
Disconnect the connectors and cables at the back of the original car radio

6. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane head unit
Check all the accessories for the new Seicane head unit

7. Make the original car’s connector plug to the new car radio’s power connector. And Make sure the rest of connectors and cables are plugged to the radio’s right interfaces.

Make the original car's connector plug to the new car radio's power connector. And Make sure the rest of connectors and cables are plugged to the radio's right interfaces
Make the original car’s connector plug to the new car radio’s power connector. And Make sure the rest of connectors and cables are plugged to the radio’s right interfaces

8. For the further confirmation of the right connecting of all connectors and cables, you can refer to the following wiring diagram.

For the further confirmation of the right connecting of all connectors and cables, you can refer to the following wiring diagram
For the further confirmation of the right connecting of all connectors and cables, you can refer to the following wiring diagram

9. Make the connector plug to the back of the trim panel of the new car radio.

Make the connector plug to the back of the trim panel of the new car radio
Make the connector plug to the back of the trim panel of the new car radio

10. Carefully place the new car radio in the dashboard.

11. Put everything into their original place. All the installation is done.

 

Above is the whole removal and installation process of a 2014 2015 2016 Subaru Forester car radio. If you come across any problems you don’t know how to deal with, you can seek help from your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard for you to install the new car radio, you can directly arrange a professional technician to help you with the installation.

While for the car radio installation, if you have no ideas, you can check out the following link which is a remarkable 2014 2015 2016 Subaru Forester car radio from Seicane.

https://www.seicane.com/android-hd-touchscreen-in-dash-radio-for-2014-2015-2016-subaru-forester-gps-navigation-bluetooth-music-usb-audio-system-support-backup-camera-digital-tv-1080p-video-dvr-steering-wheel-control-s169208g


This all-in-one car radio is running on the latest and mot stable Android 8.0 operation system and a powerful 8-core CPU processor as well as 4GB RAM and 32GB ROM to enhance its capabilities, configurations and performance, therefore it can be regarded as one of the best replacements for your factory radio.

With the assistance of the worldwide real-time GPS navigation system of high accuracy, you can easily locate where you are and navigate to any locations you would like to go to according to turn-by-turn directions and voice prompts. Therefore, even you are traveling around an unfamiliar place, with this unit’s help, you won’t get lost any longer.

What’s more, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, both Bluetooth hands-free phone calls and Bluetooth streaming music are available for you to gain more convenience and enjoyment.

If you like this unit, just add it to your shopping cart.

How to Remove and Install a 2016 Jeep Renegade Car Radio with Touch Screen Bluetooth GPS Navigation Function

2016 Jeep Renegade car radio after installation

If you are fed up with your factory radio, why not remove it and install a new multifunctional one? Since nowadays most car radios are plug and play, it is not very difficult to install the new car radio. This article will mainly introduce how to remove and install the new car radio for 2016 Jeep Renegade. If you own the same or similar dashboard and would like to upgrade your in-car life,  you can carefully read the following installation steps.

2016 Jeep Renegade car radio after installation
2016 Jeep Renegade car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2016 Jeep Renegade car radio installation guide

1. Start by removing the car radio trim panel using a flat pry tool.

Start by removing the car radio trim panel using a flat pry tool
Start by removing the car radio trim panel using a flat pry tool
1-1
1-1

2. Use a screwdriver to remove screws that are holding the radio on the dashboard.

Use a screwdriver to remove screws that are holding the radio on the dashboard
Use a screwdriver to remove screws that are holding the radio on the dashboard

3. Gently pull the original radio out from the dash.

Gently pull the original radio out from the dash
Gently pull the original radio out from the dash

4. Disconnect all the connectors and cables at the back of the radio.

Disconnect all the connectors and cables at the back of the radio
Disconnect all the connectors and cables at the back of the radio

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original radio’s plugs.

8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put the new Seicane car radio into the dash.

10. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can be helpful for you. If you are not very clear about every steps before installation, it is suggested that you should consult your dealer, communicate with someone experienced or turn to a professional for help. What’s more, it is necessary for you to pick an ideal car radio for your beloved car. If you have no idea that which kind of car radio can fit your car, you can refer to the following link which is a remarkable 2016 Jeep Renegade car radio from Seicane. For more details, please click:

https://www.seicane.com/2016-jeep-renegade-touchscreen-android-radio-gps-navigation-system-with-usb-bluetooth-wifi-1080p-aux-mirror-link-steering-wheel-control-s04131

This car radio is running on the stable Android 6.0 operation system and a powerful quad-core CPU processor, so it has strong capabilities and performance to be regarded as one of your best choices to replace your factory radio.

Even you don’t have a good sense of directions, you won’t get lost when you travel around an unfamiliar place. Under the guidance of the turn-by-turn directions and voice prompts, you are able to easily know your current locations and navigate to your desired destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Additionally, thanks to the wireless Bluetooth technology, without taking your hands off the steering wheel, you can dial, answer, reject and mute hands-free phone calls as well as enjoy your favorite music streaming from your phone music playlists with the synchronization between your Bluetooth-enabled mobile phone and this car radio.

Wish you like this unit. Good luck!