How to easily upgrade a 2004-2010 Toyota Sienna car radio with DVD Player Backup Camera HD Touch Screen 3G WIFI Steering Wheel Control Bluetooth

2004-2010 Toyota Sienna car radio after installation

If you are going to upgrade your factory radio, you can find a step-by-step installation guide to help you. The following is a detailed 2004-2010 Toyota Sienna car radio installation instruction from Seicane. If you also have a2004-2010 Toyota Sienna, it’s helpful for you during the process of the installation.

2004-2010 Toyota Sienna car radio after installation
2004-2010 Toyota Sienna car radio after installation

Some tips before the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2004-2010 Toyota Sienna car radio installation steps

Step 1.The original car radio.

The original car radio
The original car radio

Step 2.Remove the vertical panels to the right and left of the stereo and climate control system.

You can remove them by prying up on the bottom edge of the panel.

Prying up the panel to the left of the stereo or climate control center
Prying up the panel to the left of the stereo or climate control center

Step 3.Disconnect the wiring from the side panel.

The left panel has two wiring connectors and the right one only has one.  Each connector has a tab you must press in, in order to slide out the connector.  Be careful not to pull on the wires but pull on the plastic connector.

3-1. Left Panel connector release tab locations.
3-1. Left Panel connector release tab locations
3-2.Left Panel lower connector release tab location
3-2.Left Panel lower connector release tab location

Step 4.Remove the center channel speaker grill panel above the stereo.

The panel sits down into the dash and tucks under on the bottom (rear) edge and snaps down on the top edge. The front edge of the panel has three tongues that tuck into the top of the stereo so life tup the back edge and then pull the tongues out of their slots.

4-1.Prying up the top (center channel speaker) panel
4-1.Prying up the top (center channel speaker) panel
4-2.Removing the top panel–you can see the tongues that slip down into the top edge of the stereo
4-2.Removing the top panel–you can see the tongues that slip down into the top edge of the stereo

Step 5. Remove the center speaker. Then disconnect the speaker wiring harness.

There are two 10mm hex head nuts that secure it.

5-1.Center Channel Speaker 10-mm nut head bolts
5-1.Center Channel Speaker 10-mm nut head bolts
5-2.Press the tab to release the speaker wiring connector
5-2.Press the tab to release the speaker wiring connector

Step 6.Remove the 4 10mm hex head nuts from the stereo receiver (2 on each side).

These 4 screws hold the stereo in place via the bracket that is screwed to each side of the stereo.

6-1.Left stereo mounting bolt locations
6-1.Left stereo mounting bolt locations
6-2.Right stereo mounting bolt locations
6-2.Right stereo mounting bolt locations

Step 7.Disconnect the wiring from the stereo.

Gradually pull the stereo straight out.  There are five connectors, the left three have a tab you must press in, to release them and the two black ones pull straight out.

7-1.The 5 connector locations tab locations are marked with arrows below
7-1.The 5 connector locations tab locations are marked with arrows below
7-2.Stereo wiring connector release tab locations
7-2.Stereo wiring connector release tab locations
7-3.Dash with stereo removed
7-3.Dash with stereo removed

Step 8. If necessary, transfer the bracket from each side of the old stereo to the replacement.

If your replacement stereo did not come with mounting brackets then you will need to remove the ones from the old one and place them on the new. There are 4 10-mm headed hex screws on each of the two brackets.

Bracket bolt locations
Bracket bolt locations

Step 9.Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

Step 10. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

Step 11. Connect the Seicane car radio to your original car radio ‘s plugs.

Step 12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 13.Put the new Seicane car radio into the dash.

Step 14. Put everything into their original place. All the installation is done.

Now can you install your new radio in you car under the guidance of this detailed installation guide specially for a 2004-2010 Toyota Sienna car radio? If not, don’t worry, you can ask a professional for help. If there is any question, you can consult your dealer. But if you don’t have an ideal radio for your car, I’d like to recommend this advanced2004-2010 Toyota Sienna car radio from Seicane to you. Here’s the link, please check out the following link for more details:

http://www.seicane.com/android-gps-navigation-system-for-2004-2010-toyota-sienna-with-dvd-player-backup-camera-hd-touch-screen-3g-wifi-steering-wheel-control-bluetooth-s063812y

This great 2004-2010 Toyota Sienna car radio comes with an attractive interface for you to improve your in-car environment, you can change the wallpaper and car logo according to your own preference.

You can also easily get access to hands-free calls to keep safe in motion when you simply sync your compatible mobile phone with this unit via Bluetooth technology. And you can stream music to relax in this way. It also supports phonebook function, so that you can download your contact information from your phone in this unit and directly search for the contact number on it. Go with this fantastic 2004-2010 Toyota Sienna car radio and enjoy all your driving.