Clever Method on a 2009-2013 HONDA PILOT Radio Removal and Installation with An Aftermarket Audio Sound System

Posted on by — 22 Comments ↓ 32,477 views

To keep your passengers relaxed in the back seats of your car, it is necessary for you to upgrade your factory radio by installing a new aftermarket stereo which is equipped with a lot of practical and entertainment features. If you own a 2009-2013 HONDA PILOT, and plan to upgrade your factory radio, you can read the following related installation steps to help with your installation.

2009-2013 HONDA PILOT car radio after installation
2009-2013 HONDA PILOT car radio after installation

Tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2009-2013 HONDA PILOT car stereo installation steps

1. The original car radio.

The original car radio

2. Start by moving shift lever into lower position.

Start by moving shift lever into lower position

3. Using your pry tool, carefully pry loose left dash panel and slide over shifter. Then use the pry tool to remove the right panel.

Using your pry tool, carefully pry loose left dash panel and slide over shifter. Then use the pry tool to remove the right panel
3-1
3-1
3-2

4. Using a Philip head screwdriver to unscrew screws that fix the pocket and then remove it.

Using a Philip head screwdriver to unscrew screws that fix the pocket and then remove it

5. Unscrews four screws that are holding the radio and then take out the radio.

Unscrews four screws that are holding the radio and then take out the radio

6. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

7. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

8. Connect the Seicane car stereo to your original stereo’s plugs.

9. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car stereo into the dash.

11. Put everything into their original place. All the installation is done.

 

Before the installation, please make clear every step. If you have any doubts, you can consult your dealer or ask someone experienced to help you. But if you still think it hard to finish the installation by yourself, you’d better go to a car stereo upgrade center to arrange a technician to install the stereo. Anyway, first of all, please check whether your new car stereo is compatible with your car or not. If not, here I would like to share a 2009-2013 HONDA PILOT gps navi dvd car stereo from Seicane with you. Please click:

http://www.seicane.com/7-inch-1024-600-touch-screen-2009-2013-honda-pilot-android-4-4-gps-navigation-system-with-3-g-wifi-bluetooth-tpms-dvr-obdii-rear-camera-aux-steering-wheel-control-mirror-link-1080p-quad-core-cpu-s083706

This Seicane 2009-2013 HONDA PILOT car stereo is based on the Pure Android 6.0 operation system and a R16 1.6 GHz Quad-core CPU, so you are able to embrace a brand new smoother and faster operation experience than ever. Even though you don’t have a good sense of direction, you are capable of finding the best way to get to your destinations with the help of the powerful 3D GPS navigation system in high precision. What’s more, with the help of the wireless Bluetooth technology, hands-free calls and Bluetooth music are both available if you connect your Bluetooth-enabled cell phone with this unit. If you like this car stereo, don’t forget to add it to your cart. Good luck to you!

How to Upgrade a 2007-2011 Toyota CAMRY Head Unit with GPS Navigation Sound System Wisely

Posted on by — 6 Comments ↓ 20,800 views
2007-2011 Toyota CAMRY Head Unit after installation

The image shown below is a Seicane 2007-2011 Toyota CAMRY head unit after installation. This head unit comes with a variety of practical and entertainment features, which can meet almost all your different needs in car. If you own a 2007-2011 Toyota CAMRY, and plan to upgrade your factory radio with a new head unit to improve your in-car environment and driving experience, you can take the following installation guide as a reference to help with your upgrade.

2007-2011 Toyota CAMRY Head Unit after installation
2007-2011 Toyota CAMRY Head Unit after installation

Tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007-2011 Toyota CAMRY head unit installation guide

1. The original car radio.

The original car radio
The original car radio

2. Make sure that your car engages the parking brake.

3. Rotate the shift lever knob counterclockwise.

Rotate the shift lever knob counterclockwise
Rotate the shift lever knob counterclockwise

4. Grab and remove the two side panels.

Grab and remove the two side panels
Grab and remove the two side panels

5. Remove the panel around the shift lever and then unplug the connector at the backside.

Remove the panel around the shift lever and then unplug the connector at the backside
Remove the panel around the shift lever and then unplug the connector at the backside
5-1
5-1
5-2
5-2

6. Remove the plastic part shown in the following picture and then unplug the connector at the backside.

Remove the plastic part shown in the following picture and then unplug the connector at the backside
Remove the plastic part shown in the following picture and then unplug the connector at the backside

7. Unscrew two screws that are holding the pocket.

Unscrew two screws that are holding the pocket
Unscrew two screws that are holding the pocket
7-1
7-1

8. Take out the pocket and disconnect the connectors at the back of it.

Take out the pocket and disconnect the connectors at the back of it
Take out the pocket and disconnect the connectors at the back of it
8-1
8-1
8-2
8-2

9. Use a removal tool to pry the air vent and then remove it.

Use a removal tool to pry the air vent and then remove it
Use a removal tool to pry the air vent and then remove it
9-1
9-1

10. There are two top screws and two bottom screws fix the radio on the dashboard. Remove them with a screwdriver.

There are two top screws and two bottom screws fix the radio on the dashboard. Remove them with a screwdriver
There are two top screws and two bottom screws fix the radio on the dashboard. Remove them with a screwdriver
10-1
10-1

11. Take out the original car radio gently.

Take out the original car radio gently
Take out the original car radio gently

12. Disconnect the connectors and cables at the back of the radio.

13. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane head unit
Check all the accessories for the new Seicane head unit

14. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane head unit
Connect the harnesses to the back of the new Seicane head unit

15. Connect the Seicane head unit to your original stereo’s plugs.

16. Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

17. Put the new Seicane head unit into the dash.

18. Put everything into their original place.

 

Wish you can learn something from the above installation guide. Before the installation, please make clear every step. If you have any questions, you can seek advice from your dealer or ask a professional for help. Besides, you can also go straightly to a head unit upgrade centre to install you head unit. Anyway, first of all, please check the compatibility between your new head unit and your car. If you don’t have any ideas about it, you can refer to the following link which is about a great 2007-2011 Toyota CAMRY bluetooth gps dvd head unit from Seicane, please click:

http://www.seicane.com/9-inch-oem-android-radio-capacitive-touch-screen-for-2007-2011-toyota-camry-support-3g-wifi-bluetooth-gps-navigation-system-tpms-dvr-obd-ii-aux-headrest-monitor-control-video-rear-camera-usb-sd-s082706

This Seicane 2007-2011 Toyota CAMRY head unit, equipped with both upgraded features and new functions, is ideal for you to replace your factory radio.

Featured with the high-end 3D GPS navigation system, this head unit can guide you to wherever you want to go through turn-by-turn directions and voice prompts. And the Bluetooth technology which enables you to dial, receive or reject as well as enjoy streaming music is also supported in this head unit to bring safety, convenience and enjoyment for you. Just enjoy your driving with this head unit installed in your car. Good luck to you!

How to Upgrade a 2015 2016 Mercedes-Benz SMART Car Sound System with Touch Screen Radio Navigation

Posted on by — 4 Comments ↓ 5,803 views
2015 2016 Mercedes-Benz SMART Car Sound System after installation

Nowadays, it won’t cost much money to replace a factory radio, so more and more car owners tend to replace the factory radio with a new one. If you are fed up with your factory radio due to its single function, you can easily upgrade it which help you not only gain a better driving experience but also catch up with the trend. Here comes a step-by-step 2015 2016 Mercedes-Benz SMART Car Sound System installation guide from Seicane for your reference to help with the installation.

2015 2016 Mercedes-Benz SMART Car Sound System after installation
2015 2016 Mercedes-Benz SMART Car Sound System after installation

Tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2015 2016 Mercedes-Benz SMART car radio installation guide

1. Remove the decoration trim strips both on the left side and right side of the radio.

Remove the decoration trim strips both on the left side and right side of the radio
Remove the decoration trim strips both on the left side and right side of the radio
1-1
1-1
1-2
1-2

2. Use a plastic removal tool to pry the gap.

Use a plastic removal tool to pry the gap
Use a plastic removal tool to pry the gap
2-1
2-1
2-2
2-2

3. Gently take out the original radio.

Gently take out the original radio
Gently take out the original radio
3-1
3-1

4. Unplug the connectors and cables at the back of the radio.

5. Check all the accessories for the new Seicane car radio.

6. Connect the harnesses to the back of the new Seicane car radio.

7. Connect the Seicane car radio to your original stereo’s plugs.

8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put the new Seicane car radio into the dash.

10. Put everything into their original place. All the installation is done.

 

Wish you can gain something useful from the above car radio installation guide. If you have any doubts, you can seek help from your dealer or a professional. Besides, before the installation, it is fairly necessary for you to check the compatibility of your new car radio. If the radio is not suitable enough, you can refer to this modern 2015 2016 Mercedes-Benz SMART Car Sound System from Seicane. Here is the link, please click:

http://www.seicane.com/9-inch-oem-android-radio-capacitive-touch-screen-for-2015-2016-mercedes-benz-smart-support-3g-wifi-bluetooth-gps-navigation-system-tpms-dvr-obd-ii-aux-headrest-monitor-control-video-rear-camera-usb-sd-s082651

Specially designed for 2015 2016 Mercedes-Benz SMART, this great car radio comes with a variety of functions and features to help you gain a better driving experience, which include 3D GPS navigation system, DVD player, Bluetooth technology, Backup camera, Wi-Fi, etc. Because of these practical functions and entertainment features, almost all your different needs can be satisfied by this multifunctional radio. Take the 3D GPS navigation system as an example. Under the guidance of the turn-by-turn directions and voice prompts provided by the GPS function, you can easily reach your destinations while enjoying your favorite music at the same time along the way. Don’t hesitate to install it in your beloved car and wish you enjoy your driving!

How to Install a 2013 2014 2015 Suzuki S-Cross Stereo Audio with Bluetooth CD GPS Navigation

Posted on by — 2 Comments ↓ 3,779 views
2013 2014 2015 Suzuki S-Cross Stereo Audio after installation

If you’re going to replace your factory radio with a new aftermarket car stereo but worry about the complicated installation, you can feel relieved now as the installation of a car stereo is actually not difficult. With a correct installation guide, you can also try to install the car stereo on your own. Today I would like to introduce an easy-to-understand installation instruction for a car stereo, and if you have the same or similar dashboard, you can read this 2013 2014 2015 Suzuki S-Cross car stereo installation instruction carefully.

2013 2014 2015 Suzuki S-Cross Stereo Audio after installation
2013 2014 2015 Suzuki S-Cross Stereo Audio after installation

Tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2013 2014 2015 Suzuki S-Cross car stereo installation instruction

1. Pry the indicator light with a plastic knife and disconnect the connector at the back of it.

Pry the indicator light with a plastic knife and disconnect the connector at the back of it
Pry the indicator light with a plastic knife and disconnect the connector at the back of it
1-1
1-1

2. Remove the air vent with a plastic removal tool.

Remove the air vent with a plastic removal tool
Remove the air vent with a plastic removal tool

3. Remove two top screws that are holding the radio.

Remove two top screws that are holding the radio
Remove two top screws that are holding the radio

4. Gently take out the original radio.

Gently take out the original radio
Gently take out the original radio

5. Disconnect the connectors and cables at the back of the radio.

Disconnect the connectors and cables at the back of the radio
Disconnect the connectors and cables at the back of the radio

6. Check all the accessories for the new Seicane car stereo.

7. Connect the harnesses to the back of the new Seicane car stereo.

8. Connect the Seicane car stereo to your original stereo’s plugs.

9. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car stereo into the dash.

11. Put everything into their original place. All the installation is done.

 

That’s all about how to remove and install a car stereo for 2013 2014 2015 Suzuki S-Cross. Before you start the work, please make clear every specific step. It’s quite normal if you encounter problems during the process of the installation. In that case, you can seek help from a professional or your dealer. To help you better finish the installation, I’d like to share a 2013 2014 2015 Suzuki S-Cross gps bluetooth car stereo from Seicane with you, please click:

http://www.seicane.com/9-inch-quad-core-android-full-touchscreen-2013-2014-2015-suzuki-s-cross-radio-gps-head-unit-with-bluetooth-wifi-4g-usb-obd2-aux-backup-camera-dvr-steering-wheel-control-s30954

This 2013 2014 2015 Suzuki S-Cross car stereo possesses higher configurations for you to upgrade your factory radio, which include the advanced Android 5.0.1 operation system as well as a powerful R16 1.8GHz A9 Quad-core CPU. Take the practical functions as examples, the 3D built-in GPS navigation system of high accuracy can provide lane assist, 3D street view, landmark display, route planning, voice prompts and turn-by-turn direction for you to find your way to a variety of locations. Besides, you can utilize its built-in Bluetooth to wirelessly pair your enabled mobile phone to make and receive hands-free calls and stream audio to keep safe and enjoyable. Wish you enjoy your trip accompanied by this intelligent car stereo!

How to Set Up a 2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio with Aftermarket Navigation Sound System

Posted on by — No Comments ↓ 10,550 views
2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio after installation

First of all, please look at the following image which is a 2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio after installation. It looks very good, isn’t it? If you also own a 2012 2013 2014 Chevy Chevrolet Malibu and plan to upgrade your factory radio with a brand new all-in-one car stereo, you can try to remove the factory radio and install a new stereo on your own. Now I’d like to share a 2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio installation guide from Seicane for your reference.

2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio after installation
2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2012 2013 2014 Chevy Chevrolet Malibu car stereo installation guide

1. Pry the panel around the shift lever with the plastic removal tool.

Pry the panel around the shift lever with the plastic removal tool
Pry the panel around the shift lever with the plastic removal tool
1-1
1-1

2. Remove the surrounded trim panel. Please use a plastic removal tool.

Remove the surrounded trim panel. Please use a plastic removal tool
Remove the surrounded trim panel. Please use a plastic removal tool
2-1
2-1

3. Use a screwdriver to remove all the screws that fixed the AC control and the radio.

Use a screwdriver to remove all the screws that fixed the AC control and the radio
Use a screwdriver to remove all the screws that fixed the AC control and the radio

4. Remove all function control panels and the radio.

5. Unplug the connectors at the back of the stereo.

6. Check all the accessories for the new Seicane car stereo.

7. Connect the harnesses to the back of the new Seicane car stereo.

8. Connect the Seicane car stereo to your original stereo’s plugs.

9. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car stereo into the dash.

11. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can do you some help. If you encounter any questions during the whole process of the installation, you can consult your dealer or seek help from a professional. Besides, before the installation, please confirm whether you have a compatible car stereo or not. If not, you can refer to a 2012 2013 2014 Chevy Chevrolet Malibu Bluetooth Radio from Seicane. Here is the link, please click:

http://www.seicane.com/9-inch-android-2012-2013-2014-chevy-chevrolet-malibu-radio-gps-hd-1024-600-touchscreen-bluetooth-obd2-backup-camera-digital-tv-4g-wifi-steering-wheel-control-mirror-link-s30935

Loaded with a wide range of comprehensive functions, this new aftermarket car stereo is an ideal car stereo to replace your factory radio for 2012 2013 2014 Chevy Chevrolet Malibu. You are able to easily get to anywhere you would like to go under the guidance of the turn-by-turn directions and voice prompts provided by its built-in GPS. And you are able to dial, receive or reject hands-free phone calls as well as enjoy Bluetooth music without keeping your hands off the steering wheel when you connect your enabled mobile phone with this car stereo. Wish you like it and good luck to you!

The Complete Tutorial on a 2013 2014 2015 Honda Accord 9 2.0L Car Stereo Upgrade with Sound System Audio Stereo Speaker GPS Navigation

Posted on by — 4 Comments ↓ 11,986 views
2013 2014 2015 Honda Accord 9 2.0L Car Stereo after installation

Nowadays, ideal car stereos are becoming more available for car owners. But you still need to pay extra money for its installation if you don’t know how to install it. However, if you have a correct guide as well as some related experience, you can finish the installation on your own which can save you a lot of money. This passage is about the installation for a multifunctional Seicane 2013 2014 2015 Honda Accord 9 2.0L Car Stereo. If you own the same dashboard, you can refer to the following detailed instruction.

2013 2014 2015 Honda Accord 9 2.0L Car Stereo after installation
2013 2014 2015 Honda Accord 9 2.0L Car Stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2013 2014 2015 Honda Accord 9 2.0L Car Stereo installation instruction

1. Use a plastic removal tool to remove the side panels.

Use a plastic removal tool to remove the side panels
Use a plastic removal tool to remove the side panels

2. Remove two screws that fix the pocket.

Remove two screws that fix the pocket
Remove two screws that fix the pocket

3. Remove the pocket.

Remove the pocket
Remove the pocket

4. Use a plastic removal tool to release the panel to the left of the radio.

Use a plastic removal tool to release the panel to the left of the radio
Use a plastic removal tool to release the panel to the left of the radio

5. Use the plastic removal tool to pry the top tray and remove it.

Use the plastic removal tool to pry the top tray and remove it
Use the plastic removal tool to pry the top tray and remove it

6. There are two top screws and two bottom screws that are holding the radio, remove them with a screwdriver.

There are two top screws and two bottom screws that are holding the radio, remove them with a screwdriver
There are two top screws and two bottom screws that are holding the radio, remove them with a screwdriver
6-1
6-1

7. Pull out the original radio and disconnect connectors at the back of it.

Pull out the original radio and disconnect connectors at the back of it
Pull out the original radio and disconnect connectors at the back of it

8. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

9. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo
Connect the harnesses to the back of the new Seicane car stereo

10. Connect the Seicane car stereo to your original stereo’s plugs.

11. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car stereo into the dash.

13. Put everything into their original place. All the installation is done.

 

Now can you finish your car stereo installation with the help of the 2013 2014 2015 Honda Accord 9 2.0L Car Stereo installation guide? If you have any questions, you can consult your dealer for advice or turn to a professional for help. Besides, before the installation, it is especially important for you to check the compatibility between your new car stereo and your car. If you don’t have any ideas, you may check out the link below which is about a 2013 2014 2015 Honda Accord 9 2.0L gps bluetooth car stereo from Seicane. Please click:

http://www.seicane.com/2013-2014-2015-honda-accord-9-2-0l-10-2-inch-1024-600-touchscreen-radio-gps-navigation-system-with-bluetooth-obd2-tpms-backup-camera-steering-wheel-control-digital-tv-dvr-4g-wifi-android-s301091

This remarkable 2013 2014 2015 Honda Accord 9 2.0L Car Stereo is powerful enough to become your best road companion. With it installed in your beloved car, you can easily get access to hands-free calls and Bluetooth music when you wirelessly connect your enabled mobile phone with this stereo through the Bluetooth module. And you can easily reach any destinations when you press the “GPS” button and make full use of turn-by-turn direction and voice prompts. Besides, thanks to its function as a multimedia player, you are able to freely enjoy music, FM/AM stereo, TV programs, movies, etc. Wish you like it.

The Best Tips on a 2005-2010 Toyota Fortuner Car Radio Replacement with Head Unit GPS Navigation Bluetooth Music System Backup Camera

Posted on by — No Comments ↓ 6,818 views
2005-2010 Toyota Fortuner Car Radio after installation

With the rapid development of science and technology, you may have a lot of things used to be in fashion but now is out of date. So as a car owner of   , you may have found your car radio is becoming incompatible with many modern features, therefore you need to upgrade your factory radio in time to catch up with trend. This article mainly introduces detailed replacement instructions of a new car radio for 2005-2010 Toyota Fortuner. If you have interest in it, just read it carefully.

2005-2010 Toyota Fortuner Car Radio after installation
2005-2010 Toyota Fortuner Car Radio after installation

Tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2005-2010 Toyota Fortuner car radio installation steps

1. The original car radio.

The original car radio
The original car radio

2. Adjust the shifter lever.

Adjust the shifter lever
Adjust the shifter lever

3. Use the plastic removal tool to remove the panel and unplug the connector behind.

Use the plastic removal tool to remove the panel and unplug the connector behind
Use the plastic removal tool to remove the panel and unplug the connector behind
3-1
3-1

4. Grab the center nob, remove it and use a screwdriver to unscrew the hidden screw.

Grab the center nob, remove it and use a screwdriver to unscrew the hidden screw
Grab the center nob, remove it and use a screwdriver to unscrew the hidden screw
4-1
4-1

5. Remove the panel with a plastic removal tool, then unplug the connectors at the back of it.

Remove the panel with a plastic removal tool, then unplug the connectors at the back of it
Remove the panel with a plastic removal tool, then unplug the connectors at the back of it
5-1
5-1
5-2
5-2

6. Remove screws that are holding the radio.

Remove screws that are holding the radio
Remove screws that are holding the radio

7. Release the clips and take out the original car radio.

Release the clips and take out the original car radio
Release the clips and take out the original car radio
7-1
7-1

8. Disconnect connectors and cables at the back of the radio.

Disconnect connectors and cables at the back of the radio
Disconnect connectors and cables at the back of the radio

9. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

10. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

11. Connect the Seicane car radio to your original radio’s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13. Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

That’s all about the installation instruction on a 2005-2010 Toyota Fortuner car radio. Wish you can learn something from it. If you have any question, you can turn to your dealer or a technician for further help. But if you haven’t got your car radio yet, I’d like to share a great 2005-2010 Toyota Fortuner car radio from Seicane. For more details, please click:

http://www.seicane.com/full-touchscreen-1024-600-2005-2010-toyota-fortuner-android-radio-gps-bluetooth-mirror-link-tpms-obd2-dvr-rearview-camera-tv-usb-4g-wifi-16g-flash-quad-core-s30702

You are able to embrace a super fluent and fast operation experience as this car radio is based on the advanced Android 5.0.1 operation system and with a powerful configuration of 1.8GHz Quad-core CPU processor. With the worldwide real-time GPS navigation system, you are able to have the best route option to arrive at your destinations accurately. And the application of the built-in Bluetooth module makes you have hands-free calls and music streaming to keep you safer and happier when your car is in motion. Besides, this car radio is compatible with various audio and video formats like CD, VCD, DVD, DIVX, MP3, etc, which can offer you a lot of fun. Wish you like it!

How to Upgrade a 2012 2013 Toyota CAMRY Bluetooth DVD Car Radio with HD Touch Screen USB Speakers CD Player GPS Navigation Quickly

Posted on by — No Comments ↓ 7,780 views
2012 2013 Toyota CAMRY Bluetooth DVD Car Radio after installation

What measures can you take to create a more comfortable and convenient car interior environment as well as upgrade a better driving experience? In my opinion, it will be a wise choice for you if you choose to replace your factory radio with a brand new car radio with not only practical but also entertainment features. And you can try to finish the installation by yourself. To help with your installation, I would like to share an installation instruction on a 2012 2013 Toyota CAMRY car radio. If you have the same dashboard, you can refer to it.

2012 2013 Toyota CAMRY Bluetooth DVD Car Radio after installation
2012 2013 Toyota CAMRY Bluetooth DVD Car Radio after installation

Here are some tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

 

2012 2013 Toyota CAMRY car radio installation instruction

1. Unclip and remove trim panels from each side of the pocket below the radio or climate control assembly.

Unclip and remove trim panels from each side of the pocket below the radio or climate control assembly
Unclip and remove trim panels from each side of the pocket below the radio or climate control assembly

2. Unclip and remove the AC vent.

Unclip and remove the AC vent
Unclip and remove the AC vent

3. Gently pry the upper dashboard housing from the radio’s trim bezel with a plastic removal tool.

Gently pry the upper dashboard housing from the radio's trim bezel with a plastic removal tool
Gently pry the upper dashboard housing from the radio’s trim bezel with a plastic removal tool

4. Remove the two upper and two lower radio mounting screws from the dashboard.

Remove the two upper and two lower radio mounting screws from the dashboard
Remove the two upper and two lower radio mounting screws from the dashboard
4-1
4-1

5. Gently remove the original radio from the dashboard and unplug connectors at the back of the radio.

Gently remove the original radio from the dashboard and unplug connectors at the back of the radio
Gently remove the original radio from the dashboard and unplug connectors at the back of the radio

6. Check all the accessories for the new Seicane car radio.

7. Connect the harnesses to the back of the new Seicane car radio.

8. Connect the Seicane car radio to your original stereo’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding about the 2012 2013 Toyota CAMRY car radio installation? If you have any question, you’re welcome to seek advice from your dealer or ask a professional for help. But first of all, you should check whether your new car radio can work well in your car or not. If not, you can refer to the link below which is about a remarkable 2012 2013 Toyota CAMRY Bluetooth dvd car radio from Seicane. Please click:

http://www.seicane.com/10-1-inch-full-touchscreen-2012-2013-toyota-camry-android-gps-navigation-system-with-radio-rearview-camera-4g-wifi-bluetooth-mirror-link-obd2-dvr-steering-wheel-control-s301043

With a lot of modern capabilities, this intelligent 2012 2013 Toyota CAMRY Bluetooth dvd car radio can become the best replacement for your factory radio. When you turn on the 3D GPS navigation system, you are able to find the most suitable route to reach your destinations accurately through turn-by-turn direction and voice prompt. Besides, keeping your hands on the steering wheel, the built-in Bluetooth module of this radio enables you to get access to hands-free calls as well as Bluetooth music through the connection between your Bluetooth-enabled mobile phone, which guarantees your safe driving to a large extent. If you like this 2012 2013 Toyota CAMRY car radio, just install it and enjoy your happy time brought by it from now on!

Quick Steps on a 2003-2013 VW VolksWagen PASSAT Seat Skoda GPS Bluetooth Car Radio Upgrade With Stereo Sound System Backup Camera USB Connection

Posted on by — No Comments ↓ 3,609 views
2003-2013 VW VolksWagen PASSAT Seat Skoda GPS Bluetooth Car Radio after installation

You may realize that although your factory radio can play CD disks and radio to relax you sometimes, it cannot be compatible with some advanced features so that it cannot meet your most needs. Under this circumstance, it is wise for you to replace the factory radio with a new aftermarket car radio. Look at the picture below which is a Seicane 2003-2013 VW VolksWagen PASSAT Seat Skoda GPS Bluetooth Car Radio after installation. You can refer to the following installation guide if you have a same or similar dashboard in your car.

2003-2013 VW VolksWagen PASSAT Seat Skoda GPS Bluetooth Car Radio after installation
2003-2013 VW VolksWagen PASSAT Seat Skoda GPS Bluetooth Car Radio after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2003-2013 VW VolksWagen PASSAT Seat Skoda car radio installation guide

1. The original car radio.

The original car radio
The original car radio

2. Remove the radio frame.

Remove the radio frame
Remove the radio frame

3. Remove screws that are holding the original car radio.

Remove screws that are holding the original car radio
Remove screws that are holding the original car radio

4. Gently take out the original car radio.

Gently take out the original car radio
Gently take out the original car radio

5. Unplug connectors and cables at the back of the radio.

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original stereo’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Wish you can gain valuable information from the above installation guide. If there is any question you cannot deal with independently, you can turn to your dealer or a professional for help. If you still think it too hard for you to install the car radio, you can just arrange a professional to install it directly. But before the installation, please confirm that you already have a suitable car radio. If not, you are recommended to click the link below which is about a 2003-2013 VW VolksWagen PASSAT Seat Skoda GPS Bluetooth Car Radio from Seicane.

http://www.seicane.com/9-inch-hd-touchscreen-2003-2013-vw-volkswagen-passat-seat-skoda-gps-navigation-system-android-3d-gps-navigation-radio-tuner-bluetooth-music-backup-camera-usb-obd2-s30901

This Seicane car radio is advanced enough to be an ideal replacement to upgrade your factory radio of 2003-2013 VW VolksWagen PASSAT Seat Skoda. When you turn on the GPS navigation function, you can be guided to find the best route to get to your desired destinations accurately through turn-by-turn direction and voice prompt. Under the Bluetooth technology, you can easily realize the connection between your enabled cell phone and this car radio so as to dial, receive or reject hands-free phone calls as well as enjoy streaming music from your phone music playlists, which promise you not only a safer but happier driving experience. Wish you like this fantastic car radio from Seicane. Good luck to you!

The Best Way to Upgrade a 2004-2010 CITROEN C4 navigation system head unit with Mirror Link Bluetooth Music OBD2 Backup Camera

Posted on by — 4 Comments ↓ 7,512 views
2004-2010 CITROEN C4 navigation system head unit after installation

First of all, please look at the following image. It is a 2004-2010 CITROEN C4 navigation system head unit after installation. It looks very wonderful, doesn’t it? Here I would like to introduce that how the car stereo installation is achieved. If you are interested in it or you also have a plan to replace your factory radio, you may read this article carefully. Perhaps you are able to learn something from it.

2004-2010 CITROEN C4 navigation system head unit after installation
2004-2010 CITROEN C4 navigation system head unit after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2004-2010 CITROEN C4 car stereo installation guide

1. The original car radio.

The original car radio
The original car radio

2. Remove the storage box; please use a removal tool if necessary.

3. Lift up the panel around the shift lever.

Lift up the panel around the shift lever
Lift up the panel around the shift lever

4. Remove the surrounding frame.

Remove the surrounding frame
Remove the surrounding frame

5. Unscrew the screws that fixed the AC control panel and then unplug the cables behind.

Unscrew the screws that fixed the AC control panel and then unplug the cables behind
Unscrew the screws that fixed the AC control panel and then unplug the cables behind
5-1
5-1

6. Plug the professional car dismantle tool into the CD player, take it out and unplug the connectors.

Plug the professional car dismantle tool into the CD player, take it out and unplug the connectors
Plug the professional car dismantle tool into the CD player, take it out and unplug the connectors

7. Remove the trim panel cover and unplug the connectors behind.

Remove the trim panel cover and unplug the connectors behind
Remove the trim panel cover and unplug the connectors behind

8. Check all the accessories for the new Seicane car stereo.

9. Connect the harnesses to the back of the new Seicane car stereo.

10. Connect the Seicane car stereo to your original stereo’s plugs.

11. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car stereo into the dash.

13. Put everything into their original place. All the installation is done.

 

With the above installation instruction, can you finish the 2004-2010 CITROEN C4 navigation system head unit installation? If there is any question, you can seek good advice from your dealer or someone experienced. If it is the first time for you to start your installation, you’d better ask a professional for help. Anyway, before the installation, please confirm that your new car stereo can fit well with your car. If it cannot work well in your car, you’d better make a better replacement. I would like to recommend a marvelous 2004-2010 CITROEN C4 navigation system head unit from Seicane. For more details, please click:

http://www.seicane.com/hd-touchscreen-2004-2010-citroen-c4-android-radio-dvd-player-gps-navigation-system-with-bluetooth-music-wifi-dab-mirror-link-obd2-backup-camera-s32691

With a large 7inch 1024*600 multi-touch screen, this intelligent car stereo can show you the best display of videos and view effect of navigation. Besides, there are also many practical and entertainment features which can improve your car interior environment and promise you a wonderful driving experience, including 3D GPS navigation system, Bluetooth music, DVD, FM/AM radio, Wi-Fi, etc. If you like this car stereo, just take it and have a ton of fun with it.