Home › 2016 › April › 08

Daily Archives: April 8, 2016

How to simply install a new 2015-2018 Toyota Sienna head unit with Capacitive Touch Screen USB SD Bluetooth 3G WiFi Video AUX

Posted on by — No Comments ↓ 7,450 views

2015-2018 Toyota Sienna car stereo GPS navigation  installation and removal guide as below will show you how to correctly and quickly install a new radio instead of old one by yourself. Or you also can easily get support from a professional to fix it.

2015-2018 Toyota Sienna car GPS DVD Player after installation

Precautions:

  1. Pleasepark the car in safe area and remove the negative cable on the vehicle battery before the remova
  2. A lever and a screwdriver need to be prepared before the installation.
  • 2015-2018 Toyota Sienna car radio installation guide
  1. Use a lever to pry along the plastic panel and remove it.
  2. Offthe panel under the 50 shift and hang it on the panel.
  3. Remove the a/c control unitrefer to the picture
  4. Unplug the back connectorsof the a/c control unit.
  5. Remove the screws holding the radio in place.
  6. Take the factory radio out of the dashboard.
  7. Disconnect the connectors at the back of factory radio.
  8. Make antennas and cables connected step by step asinstructions show, and be very careful when you are doing the installation.
  9. Put the new Seicane unit into your dashboardand check whether your connections are correct, once it’s done, you’d better to have a tidy for the cables.
  10. Check if the new Seicane unit is working well.
  11. If there is no problem, place screws andthen put trim panel back on the new Seicane unit.

Wish 2015-2018 Toyota Sienna car DVD Player installation and removal guide above is helpful.Surely you can ask for help if you could not handle it. I’d like to recommend you an excellent 2015-2018 Toyota Sienna car stereo from Seicane if you have not got suitable one yet. Go ahead and check the link below to have look:

http://www.seicane.com/10-2-inch-aftermarket-android-radio-gps-navigation-system-for-2015-toyota-sienna-with-capacitive-touch-screen-tpms-dvr-obd-ii-headrest-monitor-control-usb-sd-bluetooth-3g-wifi-video-aux-rear-camera-s082705

 

This 2015-2018  Toyota Sienna Car GPS Navigation  comes with the latest Android Radio, RAM 4GB \ ROM 64GB \ CPU 8-core \ Built-in Carplay \ 2.5D IPS Screen, Support RDS, SWC, XM radio APP etc. You can still keep the steering wheel control working after the installation of this fantastic stereo.

How to upgrade a 2007-2015 Mitsubishi LANCER head unit with GPS Navigation system Radio Capacitive Touch Screen HD 1080P Bluetooth

Posted on by — No Comments ↓ 14,879 views

Today’s tutorial article is talking about the installation and removal of 2007-2015 Mitsubishi LANCER car stereo.If you just got your new 2007-2015 Mitsubishi LANCER DVD Player,this article will be much more helpful for you by coincidence. Please check and follow detailed instructions blow step by step.

2007-2015 Mitsubishi LANCER car stereo after installation
2007-2015 Mitsubishi LANCER car stereo after installation

 

Warning :

1.Please park your car well and unplug the negative power cable to avoid any danger before you start up any work,

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

 

2007-2015 Mitsubishi LANCER GPS navigation installation guide

1.Open glove compartment (1-1) and remove screw to side panel (1-2).

 

1-1

1-1

 

1-2

1-2

2.Remove side panel by pulling toward seat.


3.Remove screw to trim panel and then gently pull trim piece toward seat.


4.Remove trim by using the tool or hands once trim piece is loose.

5.Multiple clips across trim carefully.

6.Do not remove these three screws marked on picture.

7.Gently pry edges around stereo face with panel removal tool.

8.After removing stereo face, place in safe location.

9.Disconnect the connector at the back.

10.Remove these four screws as below.

11.Move original stereo out little bit for access to harnesses behind it.

12.Remove smaller connector to give access to Seicane harnesses.

13.Insert Seicane harness into open port of new unit(13-1), connect removed harness to Seicane harness(13-2)

 

13-1

13-1

 

13-2

13-2

14.20-pin harness connects to Seicane unit.

15.Separate and test wire for +12v constant.

16.After confirmation of +12v constant, make connection with provided P-Tap, please ensure P-Tap has punctured wire and is tightly secured.

17.Fasten top cap to connect Yellow power wire.

18.Insert stripped wire as far as possible.

19.Gently secure cap and tug on wire to make sure it is secured.

20.After making cables connection, turn on stereo and test new Seicane unit till everything works well.

Hope this article helps you a lot with the installation for 2007-2015 Mitsubishi LANCER car radio.If you still have problem about it, please feel free to contact a dealer or professional for support. Surely you can check the link below for more information:

https://www.seicane.com/2014-2015-mitsubishi-lancer-android-radio-dvd-player-gps-navigation-system-bluetooth-hd-1024-600-touch-screen-mirror-link-obd2-dvr-rearview-camera-tv-1080p-video-3g-wifi-steering-wheel-control-ipod-usb-sd-s168065g

 

This Mitsubishi LANCER head unit comes with the latest Android Radio, RAM 4GB \ ROM 64GB \ CPU 8-core \ Built-in Carplay \ 2.5D IPS Screen, Support RDS, SWC, XM radio APP etc. The awesome stereo can simply pair with your Bluetooth-enabled cell phone to have hands-free calls and stream music so as to make your journey more safer and enjoyable. Besides, you can also connect a rear-view camera with it to help you park more easily.