Home › 2022 › February

Monthly Archives: February 2022

How to upgrade 2012-2014 Chevrolet S10 Radio navigation system support Bluetooth Carplay rearview camera?

Posted on by — No Comments ↓ 102 views

Do you still use your car radios for many years? Have you consider to have better voice for your receiver within minutes? The best option to answer these question is to upgrade your car stereo by yourself as it can save money and time. Especially if you are the owner of Chevrolet S10, the feed of paying cost can be reduced and you can have better sound quality in the car life. However, not every beginner know exactly about how to upgrade their head unit without any support. And here is an referred article for those who are interested in replacing the Chevrolet head unit Navigation System, which will show you the specific steps of installation.

Before installation, you should pay attention to some important tips. First of all, you can disconnect the power and prepare some tools such as lever before the removal and the installation. Secondly, you should keep all the separate parts from the car and take great care of the dashboard to avoid scratching it during its detachment and installation.

Last but not least, you should keep handy any parts from the car and make use of all the original screws from the car as much as possible so that each related part of the unit can be fixed securely.

2012 2013 2014 Chevrolet S10 stereo removal:

1.Gently lever the upper trim housing panel from the dash with a removal tool.

2.Lever edges of side panel,release and reposition the shifter.

3.Make out 2 screws(this screw and the other corresponding one) from the storage pocket,remove car storage.

4.Make out 4 screws which are on the accessory control panel.

5.When you remove this very tough panel you should be patient and the clips will loosen.,then let panel hang to side.

6.Make out 2 screws from radio control panel,unplug the radio control panel.

7.Take out the really strange blue clip absolutely before removing the other connector,and remove the latter one.

8.Get out 2 screws which are on the radio chassis,and remove the other 2 screws which are near the top of the stereo,in order to fasten the screen.

9.Make screen out by pulling,and get behind clip out.

10.There are still 2 screws on stereo,remove them from car head unit.

11.Take stereo and connectors out.

12.Read installation instructions that within you new bought stereo,precisely make cables connection between new stereo with car.

13.After correct connection,install your new unit into your car and turn on it to test whether your actions are all right.

13.Fix 2 screws to the stereo and install the dvd player in position.

14.Make 2 screws back to the place near top of the stereo,and 2 screws to radio chassis.

15.Make other parts back to original place and don’t forget to firm their screws back to them to fix corresponding machine.

These are the whole process of installing your Chevrolet radio and you may have better understanding about how to upgrade it. But if you still think it is hard for you to install, you can ask for a technical professional for help as they will provide you the best support. Or you can also search the internet for the answers, here I would like to shard a link of Chevrolet Android unit from Seicane, where you can find many car accessories here.

This product is built-in GPS module, which promise you will never get lost when you are driving. And you can also connect your phone to the radio as it has carplay function.

If you want to know more details please visit it now.

Step-by-Step replacement of a 2013 2014 Toyota Vios Bluetooth GPS Car Radio Installation

Posted on by — No Comments ↓ 537 views

As the owner of Toyota vios, it is convenient for us to install a radio in the car as it can add much fun to our life including music, videos, broadcast etc. And if your Toyota stereo has failed and can’t work anymore, the best way to solve this problem is to replace it with a used radio that has the same part number or install an aftermarket Android Toyota unit.For most beginners, it is necessary to know the basic and easy steps of upgrading your touchscreen unit, and just as the following article shown.

Before installation, you should pay attention to some important tips. First of all, you can disconnect the power and prepare some tools such as lever before the removal and the installation. Secondly, you should keep all the separate parts from the car and take great care of the dashboard to avoid scratching it during its detachment and installation.

Last but not least, you should keep handy any parts from the car and make use of all the original screws from the car as much as possible so that each related part of the unit can be fixed securely.

2013-2016 Toyota Vios car radio installation guide

Step 1. Remove the panel with your hands,please use a plastic removal tool if necessary.

Step 2. Disconnect the connector at the back of the air vent.

Step 3. Use a screwdriver to remove four screws that are holding the original car radio.

Step 4. Gently take out the original car radio from the dashboard.

Step 5. Unplug the connectors and cables at the back of the original car radio.

Step 6. Check all the accessories for the new car radio.

Step 7. Connect the harnesses to the back of the new Seicane car radio.

Step 8. Connect the car radio to your original car radio’s plugs.

Step 9. Put the new car radio into the dash.

Step 10. Turn on the new car radio and have a comprehensive check if it works well.

Step 11. Install 4 screws back to their original position.

Step 12. Install the trim panel back to its original place.

After reading these steps, I believe you should be clear about how to install your new head unit in your Toyota vios, but don’t forget to test the functions after you complete the job. And if you think it is too hard for you , you can ask for a professional for help as he may give you technological support. One of the recommended way of solving your problem is to search the answers via Internet as there are full of variety of resources there and you can even download them without paying any money. Here I would like to share a link of Toyota Vios Aftermarket head unit from Seicane ,where you can find many car radios there. Some of the product here will have related tutorials available for everyone.

This unit is designed by 10.1 inch big screen and can support multiple functions including backup camera and Steering wheel control. During your driving trip, you can enjoy your favorite tv shows and listen to music from other countries. Plus, you can use car dvr to record every moment of your in-car life, take photos for front of vehicles and store the video in real-time while driving.

Moreover, it is operated by the latest Android 10.0 System and large memory, which will definitely offer you a smooth and stable performance. You can watch videos and make phone calls at the same time.

All in all, it deserves you to take a look now so don’t miss it anymore.

How to install Ford Edge Radio Navigation System with bluetooth Carplay easily？

Posted on by — No Comments ↓ 841 views

Last week, my old radio has been broken, which make me have to install a new one to replace it. As the beginner of installing a new head unit by myself, it is definitely a rewarding project to record this difficult but interesting process. And what encourages me most is that I just spent less than 30 minutes to finish this job, saving money and time meanwhile. In order to make more people to know these easy steps and reduce their burden of replacement, the following article of Android Ford Edge Aftermarket Radio Replacement will take as a refer for someone who are in need.

Before installation, you should pay attention to some important tips. First of all, you can disconnect the battery and prepare some tools such as lever or a screwdriver before the removal and the installation. Secondly, you should keep all the separate parts from the car and take great care of the dashboard to avoid scratching it during its detachment and installation.

Last but not least, you should keep handy any parts from the car and make use of all the original screws from the car as much as possible so that each related part of the unit can be fixed securely.

2015-2018 Ford Edge Radio Installation Instruction

Step 1.Remove the trim using a dashboard removal trim.

Step 2.Remove all four 8mm bolts that hold the radio.

Step 3.Pull out the radio carefully so that you can access the cables on the back. 

Step 4.Disconnect the cables from the back. You will need to press small release tabs then pull them out.

Step 5.Install the new Ford Edge radio in reverse and Connect the wires on the back.   

Step 6. Push the radio all the way in.

Step 7.Fasten the four screws that hold the radio in place. 

Step 8.Reinstall the dashboard trim.

Until you finished these steps, you have basically complete this installation. But there are still some safety tips that you should know. The first one tip is that you can always wear gloves and safety glasses to protect yourself. Another one is to get wheel aliment alone every time you make changes to steering or suspension component.

And if you find you have make these jobs, you can check the functions of the new radio. No one can promise accurately that you won’t make any mistakes during this procedure, but you can try to reduce the problems as you wish. If you meet any difficulty when replace the stereo, you can ask for the car dealer for help, since they will offer you the good advice. Another useful way of solving this stuff is to search for answers from the website such as Seicane , which has made aftermarket unit for over 10 years. And here is a link of Ford Edge Stereo Replacement that you can visit, where the new product just come out recently.

It comes a vertical screen which is 9.7 inch in size, and it looks very glossy, plus an Android 10 system and 8-core CPU, certainly it must be operated very smooth and keeps stable performance.

If you want to know more information about the details, just click it now.

How to Install BMW X1 F48 navigaion GPS head unit in your car？

Posted on by — No Comments ↓ 669 views

Definitely, it is lucky for those we own BMW as it has better function in the car but meanwhile it is also a challenge for those who have no knowledge about how to use it effectively. To increase some entertainment for our driving trip, installing a new head unit for BMW X1 F48 NBT system head unit is a good option as it is built in various function and maintain all original car’s function. But the difficult point lies on the steps of the whole installation process, which is why the following article has been written to take as a assistant tool for those we need help.

Before installation, you should pay attention to some important tips. First of all, you can disconnect the power and prepare some tools such as lever before the removal and the installation. Secondly, you should keep all the separate parts from the car and take great care of the dashboard to avoid scratching it during its detachment and installation.

Last but not least, you should keep handy any parts from the car and make use of all the original screws from the car as much as possible so that each related part of the unit can be fixed securely.

Installation guide of BMW X1 F48 2016-2017 NBT Radio

1.Lever button control assembly and Pull out it.

2.Disconnect the wiring and 2 connectors revealed.

3.Pry decoration trim and Unplug the wires here.

4.Take off 2 screws.

5.Pull out the frame of OEM screen and OEM screen.

6.Disconnect the wiring and Lever bottom panel of the screen.

7.Take off the panel and the 2 screws.

8.Pull out OEM head unit and Unplug the main power cable.

9.Lever the OEM buckle of fiber Optical and Unplug the fiber optical connector(if with OEM fiber optical).

10.Connect the unplugged fiber optical connector with new wiring (if with OEM fiber optical).

11.Install the CD unit and fix 2 screws.

12.Take off 4 metal buckles from OEM bottom panel and Put them on new bottom panel.

13.Install the new panel, then Connect the new wiring and original wiring to the new screen.

14.Install the new screen, then Fix 2 marked screws and Connect the wires.

15.Put the AC vent board back, then Connect wiring of the button assembly.

16.Install the assembly.

After reading the above steps, I believe you should have clear idea about how to upgrade your receiver, especially for those who decides to install it by themselves. As the first time to install the radio, you have to admit that you may probably meet some problems during this procedure. And you can search for help from your companion or go to the neighbor store to ask for the technology support, which will give you the quick response as long as you buy their service. If you think it is too hard for you to finish alone, you can visit some website from google and watch some relative tutorials. Here I would like to share a link of BMW X1 F48 Aftermarket stereo replacement, which has just new been released recently. And it has some installation videos and articles, which may help you in some degree.

One of powerful features of the product is it’s super easy to install, you just need to replace original car’s screen with this unit, no need to replace the whole radio system which takes many time as well needs some complicated steps.

It not only keeps all original car functions, but comes awesome features include original radio, DSP setting, supporting 4G network, ADH camera, OBDII and so on, adding more fun to your drive.

In a word, if you want to know more details about it, don’t wait to search the answer on our website and leave your comment there.